Home | Television & Video |

VideoSecu ML531BE TV Wall Mount for most 22"-55" LED LCD Plasma Flat Screen Monitor up to 88 lb VESA 400x400 with Full Motion Swivel Articulating 20 in Extension Arm, HDMI Cable & Bubble Level WP5

 
VideoSecu ML531BE TV Wall Mount for most 22"-55" LED LCD Plasma Flat Screen Monitor up to 88 lb VESA 400x400 with Full Motion Swivel Articulating 20 in Extension Arm, HDMI Cable & Bubble Level WP5

VideoSecu ML531BE TV Wall Mount for most 22"-55" LED LCD Plasma Flat Screen Monitor up to 88 lb VESA 400x400 with Full Motion Swivel Articulating 20 in Extension Arm, HDMI Cable & Bubble Level WP5
From VideoSecu

List Price: $125.00
Price: $24.99 Details

Availability: Usually ships in 24 hours
Fulfilled by Amazon and Sold by Warehouseseller

20 new or used available from $22.59

Average customer review:
( stars, based on 18270 reviews)

Product Description

The VideoSecu articulating mount is a mounting solution for 22"- 42", some models up to 55 inch (Please check VESA and Weight). The TV mount fit VESA 200x200mm/200x100/100x100 (8"x8"/8"x4"/4"x4"). This wall mount comes with 4 removable mount adapters. It can extend the VESA to 400x400 400x300 400x200 300x300 300x200 (16"x16"/16"x12"/16"x8"/12"x12"/12"x8"). Please check your TV VESA; these are square or rectangular patterns between 4 and 16 inches per side on the rear of your display. Heavy gauge steel construction provides safety loading up to 88lbs display. The high-tech look mount offers 15 degrees forward and 5 degrees backward tilt, 180 degrees of swivel and extension up to 20 inch for viewing angle and TV placement adjustment. The removable VESA plate can be taken off for easy installation.

Will the mount fit my TV?
Firstly, please check the weight of your display, it should be less than 88 lbs. Secondly, If your Monitor or TV has 4 mounting holes on the back of the screen that are 400x400 400x300 400x200 300x300 300x200 200x200mm/200x100/100x100 (16"x16"/16"x12"/16"x8"/12"x12"/12"x8" 8"x8"/8"x4"/4"x4") apart from each other vertically and horizontally this bracket will fit. In addition, please check the area inside the 4 mounting holes to make sure there are not any plugs. Otherwise, the plate may block the plugs.
Notice: This mount fits most 22-49" TVs, some up to 50 55 inch TVs manufactured in recent 3 years


Product Details

  • Size: 22-50 inch
  • Color: Black
  • Brand: VideoSecu
  • Model: ML531BE
  • Number of items: 1
  • Dimensions: 10.90" h x 2.60" w x 13.30" l, 8.80 pounds
  • Display size: 55

Features

  • Heavy guage steel supports screens up to 88 lbs. compatible with VESA (mounting hole pattern) 400x400mm/400x300mm/400x200mm/300x300mm/300x200mm/200x200mm/200x100mm/100x100mm (16"x16"/16"x12"/16"x8"/12"x12"/12"x8"/8"x8"/8"x4"/4"x4")
  • Post-installation level adjustment allows the TV to perfectly level
  • Tilt, swivel and rotate for maximum viewing flexibility; VESA plate can be taken off for easy installation by one person
  • Low Profile mount retracts to 2.2" to save space, Extends 20" from the wall
  • Standard mounting hardware,10 ft HDMI Cable and 6" 3-Axis Magnetic Bubble Level included

Customer Reviews

Most helpful customer reviews

761 of 791 people found the following review helpful.
5Great quality mount
By Waves
Bought it to mount 3 LED TVs (2x65", 1x50") in an office, chose this model mostly because of the lockable feature. I didn't use the included lag bolts because of the poor quality complaints in previous reviews. I didn't want to take the chance to strip the included bolts so I bought 5/16-9 2-1/2 lag bolts from Lowes (item 63396) and a box of 1/4" Toggler bolts (Lowes item 118084). On one of the 65" TVs and the 50" TV, the 2x4 studs were spaced perfectly and I was able to mount them using 4 lag bolts each. On the other 65" TV, the stud was about 2" off center so I put 2 lag bolts in the stud and 4 toggler bolts in the left and right most holes. I put my entire weight (200 lbs) on each mount half way extended and they held up just fine. Here are the pros and cons:

Pros:
1. Good quality mount
2. Ability to adjust the horizontal leveling (plus/minus 6 deg)
3. Lockable mount with 5 mm holes. Most pad locks you can find in stores have 6 mm shackle diameter, but I found the Master Lock 131Q has 5 mm locks and it fit just right.
4. 10 ft HDMI cable included
5. Long arms give you the option of moving the TV in almost any position.

Cons:
1. There is nothing to stop the TV from sliding from one way to the other on the two horizontal bars. That would screw up the horizontal alignment every time the TV is moved. Not sure how they didn't think about this. I used some black duct tape to prevent that. I could have drilled holes in the horizontal bars and put some screws in but duck tape was faster.
2. I wish I could have been able to use zip ties to route the cable on the wall side from the lower side to the upper side or the mount, but there are no holes to get the zip ties in.

Very happy with the purchase overall, would buy again in a heartbeat.

You can see how it looks with a 65" TV attached in the pictures below.

[...].

590 of 614 people found the following review helpful.
5Great Mount for a 60" TV
By Rubin
I mounted a 60" Sharp LED TV to this mount with no problems. I recieved it sooner than expected & it was 98% assembled out of the box. I followed the directions, took the time to do it right & it took about 20 minutes.

I always read the negative reviews first & I am baffled as to how people can have problems with this product. This mount is well made & I would recommend it to anyone that is concerned over the reviews stating it sags.

The mount can be easily installed by one person as I did below: You may need help to hang your tv on it once it is installed. I am laying this out because of the problems I read about in the other reviews.

1. Figure out where your studs are & drive a pin or finish nail on each side of it to be certain where the centers are. Make these small holes about 1/4" above where your mount holes will be drilled. These small holes will be covered by your mount.
2. Drill your first pilot hole into the center of the stud & run the first lag bolt & washer through the mount & get it near snug.
3. Extend the bracket so you can lean against it.
4. While leaning against the mount in a eyed up level position, lay your level on top of the wall bracket & get it level.
5. Pull your pencil from behind your ear & mark the second hole which is on the opposite side of your first hole.
6. Let it back down & drill the second hole in the center of the stud.
7. Move the mount back to the level position & install the lag bolt & washer.
8. Tighten the two lag bolts so they are just about crushing the mount into the wall.
8. You can now drill your bottom holes & install the lag bolts & washers. Make sure you are in the center of the studs.
10. Tighten & retighten all four lag bolts. If these are not tight, you will have problems with the TV sagging when the mount is extended. It is critical that the four lag bolt are tight against the mount. If you skip using the washers, you reduce the strength & stiffness of your mount.

Any fine tuning needed can be done on the 3 bolt swivel plate after the TV is on the mount.

The mounting bracket has holes so you can install mud rings & plates for your wiring. I will be installing a recessed power outlet on one side & a brush cover faceplate on the other for the signal cables on the other. The mounting bracket has wire chases so everything is neat & held to avoid crushing cables.

The only thing I will do to modify the mount is to drill a small hole in the upper portion of each pivot point to allow me to easily give each pivot a shot of WD-40 once in awhile. This should keep it operating smoothly & keep things from getting tweaked if it gets a little sticky from dust & oxidation.

21 of 21 people found the following review helpful.
5Works well - just what we needed
By R
Purchased this arm almost a year ago. I wanted to move the television from a table stand in front of a window to the side of the room on a wall. Our den is a square room at the front of an older New England home. The only place we had to put the television was on a stand in front of a window which blocked light and made the television the focus of the room. To shift focus off of the television we decided to invest in this arm and secure it in one of the builtin bookcases on the wall.

The process of attaching it to the wall was a bit tricky for our situation. First we took the middle shelf out of the builtin to make room for the television (which happened to be the perfect fit for the space). Then we cut a hole in the back of the builtin to access the wall. The studs were not ideally placed, but we were able to make it work by attaching a strong solid board to the studs for the arm to be bolted to. The arm is in direct contact with one stud, in the center. The outer two did not line up hence the board. Once all the placements were measured and drilled we shaped and painted a piece of wood to cover the hole and secure the arm on top of it (lining up holes for all the studs/bolts). I believe the entire process took three days with the alterations made to the builtin and attaching the arm properly. I'm sure attaching the arm can be done in an afternoon if it is simply a matter of putting it on a blank wall with studs in perfect positioning.

We are beyond pleased with the product and how it changed the look and feel of our family den. The room no longer centers around the television. We only pull the arm out when we want to watch a film together and when the television is off, it is now hidden to the side, out of focus.

The arm has held up well over the months we've had it and it swings and slides well without needing the use of much force. Worth adding the contraption to hold and conceal the wires so they're out of the way of the mechanisms in back is great and serves its purpose well!

Attached are a few photos. One is taken from the sofa on the back wall looking towards the window and table the television was originally placed on. Another shows how we can now watch the television from a chair without pulling the arm out if one person wants to sit down for a quick show on their own. One more photo attempts to show the size of the room and how out of the way the television now is. Additional photos show the arm itself as well as the matching builtin on the same wall (the middle shelf we removed can be seen on the other builtin).

See all stars, based on 18270 reviews...